diff options
Diffstat (limited to 'doc')
| -rw-r--r-- | doc/runsv.8.html | 75 | ||||
| -rw-r--r-- | doc/runsvctrl.8.html | 10 |
2 files changed, 38 insertions, 47 deletions
diff --git a/doc/runsv.8.html b/doc/runsv.8.html index ca1b997..d9e791e 100644 --- a/doc/runsv.8.html +++ b/doc/runsv.8.html @@ -37,73 +37,68 @@ and <i>service</i>/log/supervise/status, and in a human-readable format in <i>se <h2><a name='sect3'>Control</a></h2> The named pipes <i>service</i>/supervise/control, and (optionally) <i>service</i>/log/supervise/control -are provided to give commands to <b>runsv</b>. You can use <i><b>runsvctrl</b>(8)</i> to control -the service or just write one of the following characters to the named -pipe: +are provided to give commands to <b>runsv</b>. You can use <i><b>sv</b>(8)</i> to control the +service or just write one of the following characters to the named pipe: + <dl> <dt><b>u</b> </dt> -<dd>Up. If the service is not running, start it. If the service stops, -restart it. </dd> +<dd>Up. If the service is not running, start it. If the service stops, restart +it. </dd> <dt><b>d</b> </dt> -<dd>Down. If the service is running, send it a TERM signal, and -then a CONT signal. If ./run exits, start ./finish if it exists. After it stops, -do not restart service. </dd> +<dd>Down. If the service is running, send it a TERM signal, and then a +CONT signal. If ./run exits, start ./finish if it exists. After it stops, do +not restart service. </dd> <dt><b>o</b> </dt> -<dd>Once. If the service is not running, start it. Do -not restart it if it stops. </dd> +<dd>Once. If the service is not running, start it. Do not +restart it if it stops. </dd> <dt><b>p</b> </dt> -<dd>Pause. If the service is running, send it a -STOP signal. </dd> +<dd>Pause. If the service is running, send it a STOP +signal. </dd> <dt><b>c</b> </dt> -<dd>Continue. If the service is running, send it a CONT signal. -</dd> +<dd>Continue. If the service is running, send it a CONT signal. </dd> <dt><b>h</b> </dt> -<dd>Hangup. If the service is running, send it a HUP signal. </dd> +<dd>Hangup. +If the service is running, send it a HUP signal. </dd> <dt><b>a</b> </dt> -<dd>Alarm. If the -service is running, send it a ALRM signal. </dd> +<dd>Alarm. If the service +is running, send it a ALRM signal. </dd> <dt><b>i</b> </dt> -<dd>Interrupt. If the service is -running, send it a INT signal. </dd> +<dd>Interrupt. If the service is running, +send it a INT signal. </dd> <dt><b>q</b> </dt> -<dd>Quit. If the service is running, send it -a QUIT signal. </dd> - -<dt><b>1</b> </dt> -<dd>User-defined 1. If the service is running, send it a USR1 signal. </dd> - -<dt><b>2</b> </dt> -<dd>User-defined 2. If the service is running, send it a USR2 signal. </dd> +<dd>Quit. If the service is running, send it a QUIT signal. +</li><b></b><li>User-defined 1. If the service is running, send it a USR1 signal. </li><b></b><li>User-defined +2. If the service is running, send it a USR2 signal. </dd> <dt><b>t</b> </dt> -<dd>Terminate. -If the service is running, send it a TERM signal. </dd> +<dd>Terminate. If the service +is running, send it a TERM signal. </dd> <dt><b>k</b> </dt> -<dd>Kill. If the service -is running, send it a KILL signal. </dd> +<dd>Kill. If the service is running, send +it a KILL signal. </dd> <dt><b>x</b> </dt> -<dd>Exit. If the service is running, send -it a TERM signal, and then a CONT signal. Do not restart the service. If -the service is down, and no log service exists, <b>runsv</b> exits. If the service -is down and a log service exists, <b>runsv</b> closes the standard input of the -log service, and waits for it to terminate. If the log service is down, -<b>runsv</b> exits. This command is ignored if it is given to <i>service</i>/log/supervise/control. -</dd> +<dd>Exit. If the service is running, send it a TERM signal, +and then a CONT signal. Do not restart the service. If the service is down, +and no log service exists, <b>runsv</b> exits. If the service is down and a log +service exists, <b>runsv</b> closes the standard input of the log service, and +waits for it to terminate. If the log service is down, <b>runsv</b> exits. This +command is ignored if it is given to <i>service</i>/log/supervise/control. </dd> </dl> <p> -Example: to send a TERM signal to the socklog-unix service, either do -# runsvctrl term /var/service/socklog-unix<br> +Example: +to send a TERM signal to the socklog-unix service, either do # sv term +/var/service/socklog-unix<br> or<br> # echo -n t >/var/service/socklog-unix/supervise/control<br> <p> diff --git a/doc/runsvctrl.8.html b/doc/runsvctrl.8.html index f067e32..9569d30 100644 --- a/doc/runsvctrl.8.html +++ b/doc/runsvctrl.8.html @@ -57,13 +57,9 @@ is running, send it a ALRM signal. </dd> send it a INT signal. </dd> <dt><b>quit</b> </dt> -<dd>If the service is running, send it a QUIT signal. </dd> - -<dt><b>1</b> </dt> -<dd>If the service is running, send it a USR1 signal. </dd> - -<dt><b>2</b> </dt> -<dd>If the service is running, send it a USR2 signal. </dd> +<dd>If the service is running, send it a QUIT signal. +</li><b></b><li>If the service is running, send it a USR1 signal. </li><b></b><li>If the service is running, +send it a USR2 signal. </dd> <dt><b>term</b> </dt> <dd>If the service is running, send it a TERM signal. |