| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
| |
since 1.1.0, musl has nominally required a thread pointer to be setup.
most of the remaining code that was checking for its availability was
doing so for the sake of being usable by the dynamic linker. as of
commit 71f099cb7db821c51d8f39dfac622c61e54d794c, this is no longer
necessary; the thread pointer is now valid before any libc code
(outside of dynamic linker bootstrap functions) runs.
this commit essentially concludes "phase 3" of the "transition path
for removing lazy init of thread pointer" project that began during
the 1.1.0 release cycle.
|
|
|
|
|
|
|
|
|
|
|
| |
previously the implementation-internal signal used for multithreaded
set*id operations was left unblocked during handling of the
cancellation signal. however, on some archs, signal contexts are huge
(up to 5k) and the possibility of nested signal handlers drastically
increases the minimum stack requirement. since the cancellation signal
handler will do its job and return in bounded time before possibly
passing execution to application code, there is no need to allow other
signals to interrupt it.
|
|
|
|
|
|
|
|
|
|
|
|
| |
this is a new extension which is presently intended only for
experimental and internal libc use. interface and behavior details may
change subject to feedback and experience from using it internally.
the basic concept for the new PTHREAD_CANCEL_MASKED state is that the
first cancellation point to observe the cancellation request fails
with an errno value of ECANCELED rather than acting on cancellation,
allowing the caller to process the status and choose whether/how to
act upon it.
|
| |
|
|
|
|
|
| |
this requirement is tucked away in XSH 2.9.5 Thread Cancellation under
the heading Thread Cancellation Cleanup Handlers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
in practice this was probably a non-issue, because the necessary
barrier almost certainly exists in kernel space -- implementing signal
delivery without such a barrier seems impossible -- but for the sake
of correctness, it should be done here too.
in principle, without a barrier, it is possible that the thread to be
cancelled does not see the store of its cancellation flag performed by
another thread. this affects both the case where the signal arrives
before entering the critical program counter range from __cp_begin to
__cp_end (in which case both the signal handler and the inline check
fail to see the value which was already stored) and the case where the
signal arrives during the critical range (in which case the signal
handler should be responsible for cancellation, but when it does not
see the cancellation flag, it assumes the signal is spurious and
refuses to act on it).
in the fix, the barrier is placed only in the signal handler, not in
the inline check at the beginning of the critical program counter
range. if the signal handler runs before the critical range is
entered, it will of course take no action, but its barrier will ensure
that the inline check subsequently sees the store. if on the other
hand the inline check runs first, it may miss seeing the store, but
the subsequent signal handler in the critical range will act upon the
cancellation request. this strategy avoids adding a memory barrier in
the common, non-cancellation code path.
|
|
|
|
|
|
|
|
|
|
|
| |
if the order of object files in the static archive libc.a was not
respected by the linker, the old logic could wrongly cause POSIX
symbols outside of the ISO C namespace to be pulled into pure C
programs. this should not happen with well-behaved linkers, but
relying on the link order was a bad idea anyway.
files are renamed to better reflect their contents now that they don't
need names to control their order as members in the archive file.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
this patch improves the correctness, simplicity, and size of
cancellation-related code. modulo any small errors, it should now be
completely conformant, safe, and resource-leak free.
the notion of entering and exiting cancellation-point context has been
completely eliminated and replaced with alternative syscall assembly
code for cancellable syscalls. the assembly is responsible for setting
up execution context information (stack pointer and address of the
syscall instruction) which the cancellation signal handler can use to
determine whether the interrupted code was in a cancellable state.
these changes eliminate race conditions in the previous generation of
cancellation handling code (whereby a cancellation request received
just prior to the syscall would not be processed, leaving the syscall
to block, potentially indefinitely), and remedy an issue where
non-cancellable syscalls made from signal handlers became cancellable
if the signal handler interrupted a cancellation point.
x86_64 asm is untested and may need a second try to get it right.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- there is no longer any risk of spoofing cancellation requests, since
the cancel flag is set in pthread_cancel rather than in the signal
handler.
- cancellation signal is no longer unblocked when running the
cancellation handlers. instead, pthread_create will cause any new
threads created from a cancellation handler to unblock their own
cancellation signal.
- various tweaks in preparation for POSIX timer support.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
with this patch, the syscallN() functions are no longer needed; a
variadic syscall() macro allows syscalls with anywhere from 0 to 6
arguments to be made with a single macro name. also, manually casting
each non-integer argument with (long) is no longer necessary; the
casts are hidden in the macros.
some source files which depended on being able to define the old macro
SYSCALL_RETURNS_ERRNO have been modified to directly use __syscall()
instead of syscall(). references to SYSCALL_SIGSET_SIZE and SYSCALL_LL
have also been changed.
x86_64 has not been tested, and may need a follow-up commit to fix any
minor bugs/oversights.
|
|
|