From c559a3ca84a0258e4773571ae73fa7bba4c927b0 Mon Sep 17 00:00:00 2001 From: Ulrich Drepper Date: Thu, 25 Nov 1999 19:27:07 +0000 Subject: Update. 1999-11-25 H.J. Lu * stdlib/exit.c (exit): Run funtions only if __exit_funcs->idx > 0. 1999-11-25 Ulrich Drepper * manual/charset.texi (iconv Examples): Add iconv call to flush state. Reported by Andrew Clausen . 1999-11-25 Andreas Jaeger * manual/install.texi (Running make install): Better describe update from libc5. Patch by Michael Deutschmann . 1999-11-25 Andreas Jaeger * include/sys/mman.h: Remove K&R compatibility. 1999-11-15 Andreas Jaeger * misc/sys/mman.h: Use __REDIRECT for mmap, correct prototype to use __off64_t. 1999-11-25 Ulrich Drepper * iconv/iconv_prog.c (process_block): For stateful charsets write out byte sequence to get to initial state at the end of the file. which was reported to not work (which proofed to be wrong). --- manual/install.texi | 33 ++++++++++++++++++++++----------- 1 file changed, 22 insertions(+), 11 deletions(-) (limited to 'manual/install.texi') diff --git a/manual/install.texi b/manual/install.texi index 992203a056..3f98b270aa 100644 --- a/manual/install.texi +++ b/manual/install.texi @@ -232,18 +232,29 @@ shut the system down to single-user mode first, and reboot afterward. This minimizes the risk of breaking things when the library changes out from underneath. +If you're upgrading from Linux libc5 or some other C library, you need to +replace the @file{/usr/include} with a fresh directory before installing it. +The new @file{/usr/include} should contain the Linux headers, but nothing else. + +You must first build the library (@samp{make}), optionally check it +(@samp{make check}), switch the include directories and then install +(@samp{make install}). The steps must be done in this order. Not moving +the directory before install will result in an unusable mixture of header +files from both libraries, but configuring, building, and checking the +library requires the ability to compile and run programs against the old +library. + If you are upgrading from a previous installation of glibc 2.0 or 2.1, -@samp{make install} will do the entire job. If you're upgrading from -Linux libc5 or some other C library, you need to rename the old -@file{/usr/include} directory before running @samp{make install}, -or you will end up with a mixture of header files from both -libraries, and you won't be able to compile anything. You may also need -to reconfigure GCC to work with the new library. The easiest way to do -that is to figure out the compiler switches to make it work again -(@samp{-Wl,--dynamic-linker=/lib/ld-linux.so.2} should work on Linux -systems) and use them to recompile gcc. You can also edit the specs -file (@file{/usr/lib/gcc-lib/@var{TARGET}/@var{VERSION}/specs}), but -that is a bit of a black art. +@samp{make install} will do the entire job. You do not need to remove +the old includes -- if you want to do so anyway you must then follow the +order given above. + +You may also need to reconfigure GCC to work with the new library. The +easiest way to do that is to figure out the compiler switches to make it +work again (@samp{-Wl,--dynamic-linker=/lib/ld-linux.so.2} should work on +Linux systems) and use them to recompile gcc. You can also edit the specs +file (@file{/usr/lib/gcc-lib/@var{TARGET}/@var{VERSION}/specs}), but that +is a bit of a black art. You can install glibc somewhere other than where you configured it to go by setting the @code{install_root} variable on the command line for -- cgit 1.4.1